CDA HVC93 Bedienungsanleitung PDF herunterladen (Seite 9)

12 13

Fig.3

Notes:

s The hob is equipped with an anti-overheating safety device that can

be activated if the hob is installed over an oven that is not sufﬁciently

ventilated. In the event that this occurs, the control panel will show E2,

ER21 or ER40. We recommend that you increase the ventilation of the

hob by creating an opening in the side of the cabinet (8 cm x 5 cm).

s Ensure that the top rail is removed prior to installation, and that

no unit cross member is blocking the air outlets.

s If the hob is to be located above a working drawer, we recommend that

the drawer is not used for storing soft items, for example dusters or

towels; this is to minimize the risk of the cooling system air intakes being

obstructed.

How to install the hob

Overall dimensions of the hob:

Width: 900 mm Depth: 350 mm

Worktop cut-out dimensions:

Width: 880 mm Depth: 330 mm

1. Make the required hole in the worktop. Before doing this, you must

check the instructions supplied with any cooker hood to ensure that you

will have the required clearance. The cut-out (Fig.7) shows a 60mm gap

from the wall to the cut-out edge. The distance from the hob, when

ﬁtted, to the back wall is 50mm.

If a splashback/worktop upstand is to be ﬁtted, take this into account when

cutting the hole. The minimum distance that the hob should be positioned

away from the rear wall or splashback is 50mm.

2. Fix the foam seal underneath the appliance by following the outline of

the worktop upon which the hob will rest. This ensures an airtight seal

with the worktop. Do not use silicone type sealant.

Fig.5

Fig.6

400mm

600mm

Fig.7

min 4mm

Above an oven

ventilation

space

510

930

490

900

350

330

880

Fitting the Hob

Unpacking the hob:

Take care not to lose or mishandle any parts.

Fitting position of the hob:

This appliance must be installed a minimum of 50mm from any back wall

and a minimum of 180mm away from any adjacent vertical surfaces, e.g.

a tall cupboard end panel. This may be reduced to 100mm if the adjacent

surface is resistant to ﬁre (tiles or steel, for example). These dimensions are

shown in Fig.7.

Ventilation requirements:

This appliance must be installed to allow air to ﬂow freely to the air intake

and from the air outlet. Failure to allow sufﬁcient ventilation could cause

damage to the hob and constitutes incorrect installation, which is not

covered by the warranty.

If ﬁtting a cooker hood above the hob:

If a cooker hood is to be installed above the hob, the height of the hood

above the hob must be at least 600mm (650mm is recommended) (Fig.6).

If the instructions supplied with the hood dictate that the hood must be

installed at a height greater than 600mm, then that height is the minimum

required.

Wall furniture requirements:

The minimum height of any cabinet immediately above the hob is 900mm.

The minimum height of any adjacent units (including light pelmets) is

400mm, unless they are manufactured from a material resistant to ﬁre (steel,

for example)

Notes:

s Do not position this appliance above a refrigeration unit. The heat

generated may cause the refrigeration unit to fail.

s This appliance is designed to be installed into cabinet units capable

of withstanding temperatures of 65°C or greater above ambient

temperature.

s Never place perishable foods, cleaning products or ﬂammable items in

the cupboard below the appliance.

s If an oven is to be installed below the hob, the thermal safety system on

the hob will not allow the hob to be used at the same time as a pyrolytic

programme on the oven.





30 mm

51 mm

30 m

51 mm

30 mm

51 mm

40 mm

~ 2 mm

Fig.4

1 2 3 4 5 6 7 8 9 10 11

Kommentare zu diesen Handbüchern

Keine Kommentare

CDA HVC93 Bedienungsanleitung Seite 9

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Kochfelder CDA HVC93